The Angel Service, Repairs, Parts, and Upgrades for your Angel and other paintball guns.
Item(s) in Cart 0  |  $0
Home > Angel Parts > Angel 1 and A1 Fly

Predator A1 Rebuildable Ram

Part Number PR99
review 0 Review(s)
Predator A1 Rebuildable Ram
Email a friend Email a friend
Review this item Review this item
Your Price:  
Currently Out of Stock.
Free Shipping

The bullet points:

  • Fully rebuildable ram
  • Works with all Angel A1 and A1 Fly guns. 
  • Replaces the Stock, Fly, Magno, and STR rams. 
  • Public Beta Program available now. (See below for details)

The full description:

It's finally here! 

The first, and only, rebuildable ram for the Angel A1 and A1 Fly markers. This aftermarket ram is rebuildable, but we certainly didn't stop there. It's also packed full of improvements, as we analyzed, engineered, tested, and re-worked every part of this ram to make it the end-all upgrade for the Angel A1 firing system. 

The last ram you'll ever have to buy- 

If you've had an A1 for any amount of time, you are probably familiar with the ram issues. And the fact that the stock rams are not rebuildable, leaves you few options to address these issues. 

Problem #1: The A1 and A1 Fly were designed to be run on a low-pressure output HPA tank (500PSI or less). Not many people knew that, and so the more common standard output (850PSI) tank would be put on the gun. As soon as a regular output tank was used to gas up the A1, permanent and irreversible damage was caused to the ram. It may show up immediately, or it may take a little while, but a small leak would develop from the breech area of the gun. This is the first sign that your ram is dying. In reality, it's just a simple oring that needs to be replaced, but since the stock ram is not rebuildable, it is time to replace the whole unit. 

Problem #2: With regular use of the A1 and A1 Fly, the bumper inside the ram will wear down. This too is inaccessible, and therefore, not repairable. The end result will be that in the locked-forward position, your ram will not reliably hold the breech door closed, and your breech door may come flying open while shooting. 

The fact that you cannot open up the ram to service these parts, or even to lube them, means that an otherwise simple repair results in a costly and frustrating ram replacement. 

There have been some modification jobs out there, which would drill out your ram and allow them to come apart for servicing. These are good modifications, but the process is more complicated, requiring you to send your ram off to have the service done, and the success rate is not 100%. 

With the A1 out of production, along with all it's parts, the options for replacement have become very limited recently. There are virtually zero new rams in existence, and when a used one without a leak pops up on eBay, it tends to go quick! 

But we love the Angel guns far too much to watch such a great model die a slow death as users try to find a good ram to keep it going. 

Allow me to introduce you to the Predator A1 Ram. 

This project started months ago, and has seen many modifications along the way. After relentless testing, here's what we've come up with. 

Rebuildable - 

We knew the new ram would need to be simple to service. So now, with just the removal of 2 set screws, the entire ram comes apart simply and smoothly. 

All seals are replaceable, as is the bumper on the rear of the ram shaft. And to keep things simple, the bumper has been replaced with a standard #004 oring instead of the proprietary bumper which existed on the stock model. 


Since the stock ram had such a short lifespan, we decided to do the opposite with this one. We start with 2000 series aluminum (Much harder than the typical 6061 aluminum used in the paintball industry), then precision mill the body to exacting standards. Next, we apply a Type III - Hard Coat Anodize to the body, creating an even harder surface inside and out. The ram shaft and head are made of stainless steal. The end result? A ram which will certainly outlast the gun itself, and maybe even the apocalypse. 


Much thought and debate went into the tolerances inside this ram. If we make it too loose, we'll have the same problem the stock ram had, with premature leaks. Make it too tight, and the added friction may slow down the gun, taking away the signature speed Angels are known for. We landed on a tension which causes far better reliability, while not sacrificing any of the speed we've all come to love. 

Public Beta Program

All-in-all we couldn't be more pleased with the end result of the months and months that have gone into this project. However, here at The Angel Guy, we are perfectionists to a fault. We still want to do more testing! It's our relentless pursuit of perfection which put us on the map as the go-to source for Angel service work, and we don't intend to change that now. Yet, we've received so many phone calls and emails from people who desperately need a ram to bring their beloved A1 back to life that we couldn't hide this any longer. 

So, we have a limited number of fully assembled, fully tested, and production quality rams, which we've decided to release early as a part of a Beta test for our new Predator A1 Ram. 

Here's how it works:

  1. Purchase your very own Predator A1 ram from our online store. 
  2. We will ship your new ram within 24 Hours so you can install it and put it to use right away. 
  3. We will ask for your feedback on the new ram, and how it performs. 
  4. We will use your feedback, along with the other Beta testers', to make any final changes to the design. 
  5. If we do make any changes during the Beta test Program you will be shipped the updated part free of charge. (Meaning you'll always have the latest edition of the Predator A1 Ram up through the regular production release.)

We're excited to finally bring this out of the lab, and onto fields everywhere. We're also excited for you to join with us in making this the greatest possible ram for the A1 series guns!

Like all Predator products, this ram is...

Proudly made in the USA!

Feature 13

Related Items
Fly Magno Exhaust Valve Assem
Fly Magno Exhaust Valve Assem
Average Rating 0 Review(s)
Your Price: $86.95
Fly Magno Exhaust Valve Stem Pk Fly
Fly Magno Exhaust Valve Stem Pk Fly
Average Rating 0 Review(s)
Your Price: $10.95
Angel 1 ASA Reg adaptor Black
Angel 1 ASA Reg adaptor Black
Average Rating 0 Review(s)
Your Price: $34.95
Angel 1 Color Kit Olive
Angel 1 Color Kit Olive
Average Rating 0 Review(s)
Your Price: $99.95
CCM Angel Feed Neck Black Mid Rise
CCM Angel Feed Neck Black Mid Rise
Average Rating 0 Review(s)
Your Price: $29.95
Angel Oring Kit
Angel Oring Kit
Average Rating 0 Review(s)
Your Price: $19.95